Remove libjpeg and libjpeg_turbo.

third_party/libjpeg/jfdctint.c

Index: third_party/libjpeg/jfdctint.c
diff --git a/third_party/libjpeg/jfdctint.c b/third_party/libjpeg/jfdctint.c
deleted file mode 100644
index 0a78b64aee8ffd7fc6c3469495ec577a59d44ed1..0000000000000000000000000000000000000000
--- a/third_party/libjpeg/jfdctint.c
+++ /dev/null
@@ -1,283 +0,0 @@
-/*
- * jfdctint.c
- *
- * Copyright (C) 1991-1996, Thomas G. Lane.
- * This file is part of the Independent JPEG Group's software.
- * For conditions of distribution and use, see the accompanying README file.
- *
- * This file contains a slow-but-accurate integer implementation of the
- * forward DCT (Discrete Cosine Transform).
- *
- * A 2-D DCT can be done by 1-D DCT on each row followed by 1-D DCT
- * on each column.  Direct algorithms are also available, but they are
- * much more complex and seem not to be any faster when reduced to code.
- *
- * This implementation is based on an algorithm described in
- *   C. Loeffler, A. Ligtenberg and G. Moschytz, "Practical Fast 1-D DCT
- *   Algorithms with 11 Multiplications", Proc. Int'l. Conf. on Acoustics,
- *   Speech, and Signal Processing 1989 (ICASSP '89), pp. 988-991.
- * The primary algorithm described there uses 11 multiplies and 29 adds.
- * We use their alternate method with 12 multiplies and 32 adds.
- * The advantage of this method is that no data path contains more than one
- * multiplication; this allows a very simple and accurate implementation in
- * scaled fixed-point arithmetic, with a minimal number of shifts.
- */
-
-#define JPEG_INTERNALS
-#include "jinclude.h"
-#include "jpeglib.h"
-#include "jdct.h"		/* Private declarations for DCT subsystem */
-
-#ifdef DCT_ISLOW_SUPPORTED
-
-
-/*
- * This module is specialized to the case DCTSIZE = 8.
- */
-
-#if DCTSIZE != 8
-  Sorry, this code only copes with 8x8 DCTs. /* deliberate syntax err */
-#endif
-
-
-/*
- * The poop on this scaling stuff is as follows:
- *
- * Each 1-D DCT step produces outputs which are a factor of sqrt(N)
- * larger than the true DCT outputs.  The final outputs are therefore
- * a factor of N larger than desired; since N=8 this can be cured by
- * a simple right shift at the end of the algorithm.  The advantage of
- * this arrangement is that we save two multiplications per 1-D DCT,
- * because the y0 and y4 outputs need not be divided by sqrt(N).
- * In the IJG code, this factor of 8 is removed by the quantization step
- * (in jcdctmgr.c), NOT in this module.
- *
- * We have to do addition and subtraction of the integer inputs, which
- * is no problem, and multiplication by fractional constants, which is
- * a problem to do in integer arithmetic.  We multiply all the constants
- * by CONST_SCALE and convert them to integer constants (thus retaining
- * CONST_BITS bits of precision in the constants).  After doing a
- * multiplication we have to divide the product by CONST_SCALE, with proper
- * rounding, to produce the correct output.  This division can be done
- * cheaply as a right shift of CONST_BITS bits.  We postpone shifting
- * as long as possible so that partial sums can be added together with
- * full fractional precision.
- *
- * The outputs of the first pass are scaled up by PASS1_BITS bits so that
- * they are represented to better-than-integral precision.  These outputs
- * require BITS_IN_JSAMPLE + PASS1_BITS + 3 bits; this fits in a 16-bit word
- * with the recommended scaling.  (For 12-bit sample data, the intermediate
- * array is INT32 anyway.)
- *
- * To avoid overflow of the 32-bit intermediate results in pass 2, we must
- * have BITS_IN_JSAMPLE + CONST_BITS + PASS1_BITS <= 26.  Error analysis
- * shows that the values given below are the most effective.
- */
-
-#if BITS_IN_JSAMPLE == 8
-#define CONST_BITS  13
-#define PASS1_BITS  2
-#else
-#define CONST_BITS  13
-#define PASS1_BITS  1		/* lose a little precision to avoid overflow */
-#endif
-
-/* Some C compilers fail to reduce "FIX(constant)" at compile time, thus
- * causing a lot of useless floating-point operations at run time.
- * To get around this we use the following pre-calculated constants.
- * If you change CONST_BITS you may want to add appropriate values.
- * (With a reasonable C compiler, you can just rely on the FIX() macro...)
- */
-
-#if CONST_BITS == 13
-#define FIX_0_298631336  ((INT32)  2446)	/* FIX(0.298631336) */
-#define FIX_0_390180644  ((INT32)  3196)	/* FIX(0.390180644) */
-#define FIX_0_541196100  ((INT32)  4433)	/* FIX(0.541196100) */
-#define FIX_0_765366865  ((INT32)  6270)	/* FIX(0.765366865) */
-#define FIX_0_899976223  ((INT32)  7373)	/* FIX(0.899976223) */
-#define FIX_1_175875602  ((INT32)  9633)	/* FIX(1.175875602) */
-#define FIX_1_501321110  ((INT32)  12299)	/* FIX(1.501321110) */
-#define FIX_1_847759065  ((INT32)  15137)	/* FIX(1.847759065) */
-#define FIX_1_961570560  ((INT32)  16069)	/* FIX(1.961570560) */
-#define FIX_2_053119869  ((INT32)  16819)	/* FIX(2.053119869) */
-#define FIX_2_562915447  ((INT32)  20995)	/* FIX(2.562915447) */
-#define FIX_3_072711026  ((INT32)  25172)	/* FIX(3.072711026) */
-#else
-#define FIX_0_298631336  FIX(0.298631336)
-#define FIX_0_390180644  FIX(0.390180644)
-#define FIX_0_541196100  FIX(0.541196100)
-#define FIX_0_765366865  FIX(0.765366865)
-#define FIX_0_899976223  FIX(0.899976223)
-#define FIX_1_175875602  FIX(1.175875602)
-#define FIX_1_501321110  FIX(1.501321110)
-#define FIX_1_847759065  FIX(1.847759065)
-#define FIX_1_961570560  FIX(1.961570560)
-#define FIX_2_053119869  FIX(2.053119869)
-#define FIX_2_562915447  FIX(2.562915447)
-#define FIX_3_072711026  FIX(3.072711026)
-#endif
-
-
-/* Multiply an INT32 variable by an INT32 constant to yield an INT32 result.
- * For 8-bit samples with the recommended scaling, all the variable
- * and constant values involved are no more than 16 bits wide, so a
- * 16x16->32 bit multiply can be used instead of a full 32x32 multiply.
- * For 12-bit samples, a full 32-bit multiplication will be needed.
- */
-
-#if BITS_IN_JSAMPLE == 8
-#define MULTIPLY(var,const)  MULTIPLY16C16(var,const)
-#else
-#define MULTIPLY(var,const)  ((var) * (const))
-#endif
-
-
-/*
- * Perform the forward DCT on one block of samples.
- */
-
-GLOBAL(void)
-jpeg_fdct_islow (DCTELEM * data)
-{
-  INT32 tmp0, tmp1, tmp2, tmp3, tmp4, tmp5, tmp6, tmp7;
-  INT32 tmp10, tmp11, tmp12, tmp13;
-  INT32 z1, z2, z3, z4, z5;
-  DCTELEM *dataptr;
-  int ctr;
-  SHIFT_TEMPS
-
-  /* Pass 1: process rows. */
-  /* Note results are scaled up by sqrt(8) compared to a true DCT; */
-  /* furthermore, we scale the results by 2**PASS1_BITS. */
-
-  dataptr = data;
-  for (ctr = DCTSIZE-1; ctr >= 0; ctr--) {
-    tmp0 = dataptr[0] + dataptr[7];
-    tmp7 = dataptr[0] - dataptr[7];
-    tmp1 = dataptr[1] + dataptr[6];
-    tmp6 = dataptr[1] - dataptr[6];
-    tmp2 = dataptr[2] + dataptr[5];
-    tmp5 = dataptr[2] - dataptr[5];
-    tmp3 = dataptr[3] + dataptr[4];
-    tmp4 = dataptr[3] - dataptr[4];
-    
-    /* Even part per LL&M figure 1 --- note that published figure is faulty;
-     * rotator "sqrt(2)*c1" should be "sqrt(2)*c6".
-     */
-    
-    tmp10 = tmp0 + tmp3;
-    tmp13 = tmp0 - tmp3;
-    tmp11 = tmp1 + tmp2;
-    tmp12 = tmp1 - tmp2;
-    
-    dataptr[0] = (DCTELEM) ((tmp10 + tmp11) << PASS1_BITS);
-    dataptr[4] = (DCTELEM) ((tmp10 - tmp11) << PASS1_BITS);
-    
-    z1 = MULTIPLY(tmp12 + tmp13, FIX_0_541196100);
-    dataptr[2] = (DCTELEM) DESCALE(z1 + MULTIPLY(tmp13, FIX_0_765366865),
-				   CONST_BITS-PASS1_BITS);
-    dataptr[6] = (DCTELEM) DESCALE(z1 + MULTIPLY(tmp12, - FIX_1_847759065),
-				   CONST_BITS-PASS1_BITS);
-    
-    /* Odd part per figure 8 --- note paper omits factor of sqrt(2).
-     * cK represents cos(K*pi/16).
-     * i0..i3 in the paper are tmp4..tmp7 here.
-     */
-    
-    z1 = tmp4 + tmp7;
-    z2 = tmp5 + tmp6;
-    z3 = tmp4 + tmp6;
-    z4 = tmp5 + tmp7;
-    z5 = MULTIPLY(z3 + z4, FIX_1_175875602); /* sqrt(2) * c3 */
-    
-    tmp4 = MULTIPLY(tmp4, FIX_0_298631336); /* sqrt(2) * (-c1+c3+c5-c7) */
-    tmp5 = MULTIPLY(tmp5, FIX_2_053119869); /* sqrt(2) * ( c1+c3-c5+c7) */
-    tmp6 = MULTIPLY(tmp6, FIX_3_072711026); /* sqrt(2) * ( c1+c3+c5-c7) */
-    tmp7 = MULTIPLY(tmp7, FIX_1_501321110); /* sqrt(2) * ( c1+c3-c5-c7) */
-    z1 = MULTIPLY(z1, - FIX_0_899976223); /* sqrt(2) * (c7-c3) */
-    z2 = MULTIPLY(z2, - FIX_2_562915447); /* sqrt(2) * (-c1-c3) */
-    z3 = MULTIPLY(z3, - FIX_1_961570560); /* sqrt(2) * (-c3-c5) */
-    z4 = MULTIPLY(z4, - FIX_0_390180644); /* sqrt(2) * (c5-c3) */
-    
-    z3 += z5;
-    z4 += z5;
-    
-    dataptr[7] = (DCTELEM) DESCALE(tmp4 + z1 + z3, CONST_BITS-PASS1_BITS);
-    dataptr[5] = (DCTELEM) DESCALE(tmp5 + z2 + z4, CONST_BITS-PASS1_BITS);
-    dataptr[3] = (DCTELEM) DESCALE(tmp6 + z2 + z3, CONST_BITS-PASS1_BITS);
-    dataptr[1] = (DCTELEM) DESCALE(tmp7 + z1 + z4, CONST_BITS-PASS1_BITS);
-    
-    dataptr += DCTSIZE;		/* advance pointer to next row */
-  }
-
-  /* Pass 2: process columns.
-   * We remove the PASS1_BITS scaling, but leave the results scaled up
-   * by an overall factor of 8.
-   */
-
-  dataptr = data;
-  for (ctr = DCTSIZE-1; ctr >= 0; ctr--) {
-    tmp0 = dataptr[DCTSIZE*0] + dataptr[DCTSIZE*7];
-    tmp7 = dataptr[DCTSIZE*0] - dataptr[DCTSIZE*7];
-    tmp1 = dataptr[DCTSIZE*1] + dataptr[DCTSIZE*6];
-    tmp6 = dataptr[DCTSIZE*1] - dataptr[DCTSIZE*6];
-    tmp2 = dataptr[DCTSIZE*2] + dataptr[DCTSIZE*5];
-    tmp5 = dataptr[DCTSIZE*2] - dataptr[DCTSIZE*5];
-    tmp3 = dataptr[DCTSIZE*3] + dataptr[DCTSIZE*4];
-    tmp4 = dataptr[DCTSIZE*3] - dataptr[DCTSIZE*4];
-    
-    /* Even part per LL&M figure 1 --- note that published figure is faulty;
-     * rotator "sqrt(2)*c1" should be "sqrt(2)*c6".
-     */
-    
-    tmp10 = tmp0 + tmp3;
-    tmp13 = tmp0 - tmp3;
-    tmp11 = tmp1 + tmp2;
-    tmp12 = tmp1 - tmp2;
-    
-    dataptr[DCTSIZE*0] = (DCTELEM) DESCALE(tmp10 + tmp11, PASS1_BITS);
-    dataptr[DCTSIZE*4] = (DCTELEM) DESCALE(tmp10 - tmp11, PASS1_BITS);
-    
-    z1 = MULTIPLY(tmp12 + tmp13, FIX_0_541196100);
-    dataptr[DCTSIZE*2] = (DCTELEM) DESCALE(z1 + MULTIPLY(tmp13, FIX_0_765366865),
-					   CONST_BITS+PASS1_BITS);
-    dataptr[DCTSIZE*6] = (DCTELEM) DESCALE(z1 + MULTIPLY(tmp12, - FIX_1_847759065),
-					   CONST_BITS+PASS1_BITS);
-    
-    /* Odd part per figure 8 --- note paper omits factor of sqrt(2).
-     * cK represents cos(K*pi/16).
-     * i0..i3 in the paper are tmp4..tmp7 here.
-     */
-    
-    z1 = tmp4 + tmp7;
-    z2 = tmp5 + tmp6;
-    z3 = tmp4 + tmp6;
-    z4 = tmp5 + tmp7;
-    z5 = MULTIPLY(z3 + z4, FIX_1_175875602); /* sqrt(2) * c3 */
-    
-    tmp4 = MULTIPLY(tmp4, FIX_0_298631336); /* sqrt(2) * (-c1+c3+c5-c7) */
-    tmp5 = MULTIPLY(tmp5, FIX_2_053119869); /* sqrt(2) * ( c1+c3-c5+c7) */
-    tmp6 = MULTIPLY(tmp6, FIX_3_072711026); /* sqrt(2) * ( c1+c3+c5-c7) */
-    tmp7 = MULTIPLY(tmp7, FIX_1_501321110); /* sqrt(2) * ( c1+c3-c5-c7) */
-    z1 = MULTIPLY(z1, - FIX_0_899976223); /* sqrt(2) * (c7-c3) */
-    z2 = MULTIPLY(z2, - FIX_2_562915447); /* sqrt(2) * (-c1-c3) */
-    z3 = MULTIPLY(z3, - FIX_1_961570560); /* sqrt(2) * (-c3-c5) */
-    z4 = MULTIPLY(z4, - FIX_0_390180644); /* sqrt(2) * (c5-c3) */
-    
-    z3 += z5;
-    z4 += z5;
-    
-    dataptr[DCTSIZE*7] = (DCTELEM) DESCALE(tmp4 + z1 + z3,
-					   CONST_BITS+PASS1_BITS);
-    dataptr[DCTSIZE*5] = (DCTELEM) DESCALE(tmp5 + z2 + z4,
-					   CONST_BITS+PASS1_BITS);
-    dataptr[DCTSIZE*3] = (DCTELEM) DESCALE(tmp6 + z2 + z3,
-					   CONST_BITS+PASS1_BITS);
-    dataptr[DCTSIZE*1] = (DCTELEM) DESCALE(tmp7 + z1 + z4,
-					   CONST_BITS+PASS1_BITS);
-    
-    dataptr++;			/* advance pointer to next column */
-  }
-}
-
-#endif /* DCT_ISLOW_SUPPORTED */