OLD | NEW |
(Empty) | |
| 1 /* hermes.h |
| 2 * |
| 3 * Driver core for the "Hermes" wireless MAC controller, as used in |
| 4 * the Lucent Orinoco and Cabletron RoamAbout cards. It should also |
| 5 * work on the hfa3841 and hfa3842 MAC controller chips used in the |
| 6 * Prism I & II chipsets. |
| 7 * |
| 8 * This is not a complete driver, just low-level access routines for |
| 9 * the MAC controller itself. |
| 10 * |
| 11 * Based on the prism2 driver from Absolute Value Systems' linux-wlan |
| 12 * project, the Linux wvlan_cs driver, Lucent's HCF-Light |
| 13 * (wvlan_hcf.c) library, and the NetBSD wireless driver. |
| 14 * |
| 15 * Copyright (C) 2000, David Gibson, Linuxcare Australia. |
| 16 * (C) Copyright David Gibson, IBM Corp. 2001-2003. |
| 17 * |
| 18 * Portions taken from hfa384x.h. |
| 19 * Copyright (C) 1999 AbsoluteValue Systems, Inc. All Rights Reserved. |
| 20 * |
| 21 * This file distributed under the GPL, version 2. |
| 22 */ |
| 23 |
| 24 #ifndef _HERMES_H |
| 25 #define _HERMES_H |
| 26 |
| 27 /* Notes on locking: |
| 28 * |
| 29 * As a module of low level hardware access routines, there is no |
| 30 * locking. Users of this module should ensure that they serialize |
| 31 * access to the hermes_t structure, and to the hardware |
| 32 */ |
| 33 |
| 34 #include <linux/if_ether.h> |
| 35 #include <linux/io.h> |
| 36 |
| 37 /* |
| 38 * Limits and constants |
| 39 */ |
| 40 #define HERMES_ALLOC_LEN_MIN (4) |
| 41 #define HERMES_ALLOC_LEN_MAX (2400) |
| 42 #define HERMES_LTV_LEN_MAX (34) |
| 43 #define HERMES_BAP_DATALEN_MAX (4096) |
| 44 #define HERMES_BAP_OFFSET_MAX (4096) |
| 45 #define HERMES_PORTID_MAX (7) |
| 46 #define HERMES_NUMPORTS_MAX (HERMES_PORTID_MAX+1) |
| 47 #define HERMES_PDR_LEN_MAX (260) /* in bytes, from EK */ |
| 48 #define HERMES_PDA_RECS_MAX (200) /* a guess */ |
| 49 #define HERMES_PDA_LEN_MAX (1024) /* in bytes, from EK */ |
| 50 #define HERMES_SCANRESULT_MAX (35) |
| 51 #define HERMES_CHINFORESULT_MAX (8) |
| 52 #define HERMES_MAX_MULTICAST (16) |
| 53 #define HERMES_MAGIC (0x7d1f) |
| 54 |
| 55 /* |
| 56 * Hermes register offsets |
| 57 */ |
| 58 #define HERMES_CMD (0x00) |
| 59 #define HERMES_PARAM0 (0x02) |
| 60 #define HERMES_PARAM1 (0x04) |
| 61 #define HERMES_PARAM2 (0x06) |
| 62 #define HERMES_STATUS (0x08) |
| 63 #define HERMES_RESP0 (0x0A) |
| 64 #define HERMES_RESP1 (0x0C) |
| 65 #define HERMES_RESP2 (0x0E) |
| 66 #define HERMES_INFOFID (0x10) |
| 67 #define HERMES_RXFID (0x20) |
| 68 #define HERMES_ALLOCFID (0x22) |
| 69 #define HERMES_TXCOMPLFID (0x24) |
| 70 #define HERMES_SELECT0 (0x18) |
| 71 #define HERMES_OFFSET0 (0x1C) |
| 72 #define HERMES_DATA0 (0x36) |
| 73 #define HERMES_SELECT1 (0x1A) |
| 74 #define HERMES_OFFSET1 (0x1E) |
| 75 #define HERMES_DATA1 (0x38) |
| 76 #define HERMES_EVSTAT (0x30) |
| 77 #define HERMES_INTEN (0x32) |
| 78 #define HERMES_EVACK (0x34) |
| 79 #define HERMES_CONTROL (0x14) |
| 80 #define HERMES_SWSUPPORT0 (0x28) |
| 81 #define HERMES_SWSUPPORT1 (0x2A) |
| 82 #define HERMES_SWSUPPORT2 (0x2C) |
| 83 #define HERMES_AUXPAGE (0x3A) |
| 84 #define HERMES_AUXOFFSET (0x3C) |
| 85 #define HERMES_AUXDATA (0x3E) |
| 86 |
| 87 /* |
| 88 * CMD register bitmasks |
| 89 */ |
| 90 #define HERMES_CMD_BUSY (0x8000) |
| 91 #define HERMES_CMD_AINFO (0x7f00) |
| 92 #define HERMES_CMD_MACPORT (0x0700) |
| 93 #define HERMES_CMD_RECL (0x0100) |
| 94 #define HERMES_CMD_WRITE (0x0100) |
| 95 #define HERMES_CMD_PROGMODE (0x0300) |
| 96 #define HERMES_CMD_CMDCODE (0x003f) |
| 97 |
| 98 /* |
| 99 * STATUS register bitmasks |
| 100 */ |
| 101 #define HERMES_STATUS_RESULT (0x7f00) |
| 102 #define HERMES_STATUS_CMDCODE (0x003f) |
| 103 |
| 104 /* |
| 105 * OFFSET register bitmasks |
| 106 */ |
| 107 #define HERMES_OFFSET_BUSY (0x8000) |
| 108 #define HERMES_OFFSET_ERR (0x4000) |
| 109 #define HERMES_OFFSET_DATAOFF (0x0ffe) |
| 110 |
| 111 /* |
| 112 * Event register bitmasks (INTEN, EVSTAT, EVACK) |
| 113 */ |
| 114 #define HERMES_EV_TICK (0x8000) |
| 115 #define HERMES_EV_WTERR (0x4000) |
| 116 #define HERMES_EV_INFDROP (0x2000) |
| 117 #define HERMES_EV_INFO (0x0080) |
| 118 #define HERMES_EV_DTIM (0x0020) |
| 119 #define HERMES_EV_CMD (0x0010) |
| 120 #define HERMES_EV_ALLOC (0x0008) |
| 121 #define HERMES_EV_TXEXC (0x0004) |
| 122 #define HERMES_EV_TX (0x0002) |
| 123 #define HERMES_EV_RX (0x0001) |
| 124 |
| 125 /* |
| 126 * Command codes |
| 127 */ |
| 128 /*--- Controller Commands ----------------------------*/ |
| 129 #define HERMES_CMD_INIT (0x0000) |
| 130 #define HERMES_CMD_ENABLE (0x0001) |
| 131 #define HERMES_CMD_DISABLE (0x0002) |
| 132 #define HERMES_CMD_DIAG (0x0003) |
| 133 |
| 134 /*--- Buffer Mgmt Commands ---------------------------*/ |
| 135 #define HERMES_CMD_ALLOC (0x000A) |
| 136 #define HERMES_CMD_TX (0x000B) |
| 137 |
| 138 /*--- Regulate Commands ------------------------------*/ |
| 139 #define HERMES_CMD_NOTIFY (0x0010) |
| 140 #define HERMES_CMD_INQUIRE (0x0011) |
| 141 |
| 142 /*--- Configure Commands -----------------------------*/ |
| 143 #define HERMES_CMD_ACCESS (0x0021) |
| 144 #define HERMES_CMD_DOWNLD (0x0022) |
| 145 |
| 146 /*--- Serial I/O Commands ----------------------------*/ |
| 147 #define HERMES_CMD_READMIF (0x0030) |
| 148 #define HERMES_CMD_WRITEMIF (0x0031) |
| 149 |
| 150 /*--- Debugging Commands -----------------------------*/ |
| 151 #define HERMES_CMD_TEST (0x0038) |
| 152 |
| 153 |
| 154 /* Test command arguments */ |
| 155 #define HERMES_TEST_SET_CHANNEL 0x0800 |
| 156 #define HERMES_TEST_MONITOR 0x0b00 |
| 157 #define HERMES_TEST_STOP 0x0f00 |
| 158 |
| 159 /* Authentication algorithms */ |
| 160 #define HERMES_AUTH_OPEN 1 |
| 161 #define HERMES_AUTH_SHARED_KEY 2 |
| 162 |
| 163 /* WEP settings */ |
| 164 #define HERMES_WEP_PRIVACY_INVOKED 0x0001 |
| 165 #define HERMES_WEP_EXCL_UNENCRYPTED 0x0002 |
| 166 #define HERMES_WEP_HOST_ENCRYPT 0x0010 |
| 167 #define HERMES_WEP_HOST_DECRYPT 0x0080 |
| 168 |
| 169 /* Symbol hostscan options */ |
| 170 #define HERMES_HOSTSCAN_SYMBOL_5SEC 0x0001 |
| 171 #define HERMES_HOSTSCAN_SYMBOL_ONCE 0x0002 |
| 172 #define HERMES_HOSTSCAN_SYMBOL_PASSIVE 0x0040 |
| 173 #define HERMES_HOSTSCAN_SYMBOL_BCAST 0x0080 |
| 174 |
| 175 /* |
| 176 * Frame structures and constants |
| 177 */ |
| 178 |
| 179 #define HERMES_DESCRIPTOR_OFFSET 0 |
| 180 #define HERMES_802_11_OFFSET (14) |
| 181 #define HERMES_802_3_OFFSET (14+32) |
| 182 #define HERMES_802_2_OFFSET (14+32+14) |
| 183 #define HERMES_TXCNTL2_OFFSET (HERMES_802_3_OFFSET - 2) |
| 184 |
| 185 #define HERMES_RXSTAT_ERR (0x0003) |
| 186 #define HERMES_RXSTAT_BADCRC (0x0001) |
| 187 #define HERMES_RXSTAT_UNDECRYPTABLE (0x0002) |
| 188 #define HERMES_RXSTAT_MIC (0x0010) /* Frame contains MIC */ |
| 189 #define HERMES_RXSTAT_MACPORT (0x0700) |
| 190 #define HERMES_RXSTAT_PCF (0x1000) /* Frame was received in
CF period */ |
| 191 #define HERMES_RXSTAT_MIC_KEY_ID (0x1800) /* MIC key used */ |
| 192 #define HERMES_RXSTAT_MSGTYPE (0xE000) |
| 193 #define HERMES_RXSTAT_1042 (0x2000) /* RFC-1042 frame */ |
| 194 #define HERMES_RXSTAT_TUNNEL (0x4000) /* bridge-tunnel encoded
frame */ |
| 195 #define HERMES_RXSTAT_WMP (0x6000) /* Wavelan-II Management
Protocol frame */ |
| 196 |
| 197 /* Shift amount for key ID in RXSTAT and TXCTRL */ |
| 198 #define HERMES_MIC_KEY_ID_SHIFT 11 |
| 199 |
| 200 struct hermes_tx_descriptor { |
| 201 __le16 status; |
| 202 __le16 reserved1; |
| 203 __le16 reserved2; |
| 204 __le32 sw_support; |
| 205 u8 retry_count; |
| 206 u8 tx_rate; |
| 207 __le16 tx_control; |
| 208 } __packed; |
| 209 |
| 210 #define HERMES_TXSTAT_RETRYERR (0x0001) |
| 211 #define HERMES_TXSTAT_AGEDERR (0x0002) |
| 212 #define HERMES_TXSTAT_DISCON (0x0004) |
| 213 #define HERMES_TXSTAT_FORMERR (0x0008) |
| 214 |
| 215 #define HERMES_TXCTRL_TX_OK (0x0002) /* ?? interrupt on Tx co
mplete */ |
| 216 #define HERMES_TXCTRL_TX_EX (0x0004) /* ?? interrupt on Tx ex
ception */ |
| 217 #define HERMES_TXCTRL_802_11 (0x0008) /* We supply 802.11 head
er */ |
| 218 #define HERMES_TXCTRL_MIC (0x0010) /* 802.3 + TKIP */ |
| 219 #define HERMES_TXCTRL_MIC_KEY_ID (0x1800) /* MIC Key ID mask */ |
| 220 #define HERMES_TXCTRL_ALT_RTRY (0x0020) |
| 221 |
| 222 /* Inquiry constants and data types */ |
| 223 |
| 224 #define HERMES_INQ_TALLIES (0xF100) |
| 225 #define HERMES_INQ_SCAN (0xF101) |
| 226 #define HERMES_INQ_CHANNELINFO (0xF102) |
| 227 #define HERMES_INQ_HOSTSCAN (0xF103) |
| 228 #define HERMES_INQ_HOSTSCAN_SYMBOL (0xF104) |
| 229 #define HERMES_INQ_LINKSTATUS (0xF200) |
| 230 #define HERMES_INQ_SEC_STAT_AGERE (0xF202) |
| 231 |
| 232 struct hermes_tallies_frame { |
| 233 __le16 TxUnicastFrames; |
| 234 __le16 TxMulticastFrames; |
| 235 __le16 TxFragments; |
| 236 __le16 TxUnicastOctets; |
| 237 __le16 TxMulticastOctets; |
| 238 __le16 TxDeferredTransmissions; |
| 239 __le16 TxSingleRetryFrames; |
| 240 __le16 TxMultipleRetryFrames; |
| 241 __le16 TxRetryLimitExceeded; |
| 242 __le16 TxDiscards; |
| 243 __le16 RxUnicastFrames; |
| 244 __le16 RxMulticastFrames; |
| 245 __le16 RxFragments; |
| 246 __le16 RxUnicastOctets; |
| 247 __le16 RxMulticastOctets; |
| 248 __le16 RxFCSErrors; |
| 249 __le16 RxDiscards_NoBuffer; |
| 250 __le16 TxDiscardsWrongSA; |
| 251 __le16 RxWEPUndecryptable; |
| 252 __le16 RxMsgInMsgFragments; |
| 253 __le16 RxMsgInBadMsgFragments; |
| 254 /* Those last are probably not available in very old firmwares */ |
| 255 __le16 RxDiscards_WEPICVError; |
| 256 __le16 RxDiscards_WEPExcluded; |
| 257 } __packed; |
| 258 |
| 259 /* Grabbed from wlan-ng - Thanks Mark... - Jean II |
| 260 * This is the result of a scan inquiry command */ |
| 261 /* Structure describing info about an Access Point */ |
| 262 struct prism2_scan_apinfo { |
| 263 __le16 channel; /* Channel where the AP sits */ |
| 264 __le16 noise; /* Noise level */ |
| 265 __le16 level; /* Signal level */ |
| 266 u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ |
| 267 __le16 beacon_interv; /* Beacon interval */ |
| 268 __le16 capabilities; /* Capabilities */ |
| 269 __le16 essid_len; /* ESSID length */ |
| 270 u8 essid[32]; /* ESSID of the network */ |
| 271 u8 rates[10]; /* Bit rate supported */ |
| 272 __le16 proberesp_rate; /* Data rate of the response frame */ |
| 273 __le16 atim; /* ATIM window time, Kus (hostscan only) */ |
| 274 } __packed; |
| 275 |
| 276 /* Same stuff for the Lucent/Agere card. |
| 277 * Thanks to h1kari <h1kari AT dachb0den.com> - Jean II */ |
| 278 struct agere_scan_apinfo { |
| 279 __le16 channel; /* Channel where the AP sits */ |
| 280 __le16 noise; /* Noise level */ |
| 281 __le16 level; /* Signal level */ |
| 282 u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ |
| 283 __le16 beacon_interv; /* Beacon interval */ |
| 284 __le16 capabilities; /* Capabilities */ |
| 285 /* bits: 0-ess, 1-ibss, 4-privacy [wep] */ |
| 286 __le16 essid_len; /* ESSID length */ |
| 287 u8 essid[32]; /* ESSID of the network */ |
| 288 } __packed; |
| 289 |
| 290 /* Moustafa: Scan structure for Symbol cards */ |
| 291 struct symbol_scan_apinfo { |
| 292 u8 channel; /* Channel where the AP sits */ |
| 293 u8 unknown1; /* 8 in 2.9x and 3.9x f/w, 0 otherwise */ |
| 294 __le16 noise; /* Noise level */ |
| 295 __le16 level; /* Signal level */ |
| 296 u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ |
| 297 __le16 beacon_interv; /* Beacon interval */ |
| 298 __le16 capabilities; /* Capabilities */ |
| 299 /* bits: 0-ess, 1-ibss, 4-privacy [wep] */ |
| 300 __le16 essid_len; /* ESSID length */ |
| 301 u8 essid[32]; /* ESSID of the network */ |
| 302 __le16 rates[5]; /* Bit rate supported */ |
| 303 __le16 basic_rates; /* Basic rates bitmask */ |
| 304 u8 unknown2[6]; /* Always FF:FF:FF:FF:00:00 */ |
| 305 u8 unknown3[8]; /* Always 0, appeared in f/w 3.91-68 */ |
| 306 } __packed; |
| 307 |
| 308 union hermes_scan_info { |
| 309 struct agere_scan_apinfo a; |
| 310 struct prism2_scan_apinfo p; |
| 311 struct symbol_scan_apinfo s; |
| 312 }; |
| 313 |
| 314 /* Extended scan struct for HERMES_INQ_CHANNELINFO. |
| 315 * wl_lkm calls this an ACS scan (Automatic Channel Select). |
| 316 * Keep out of union hermes_scan_info because it is much bigger than |
| 317 * the older scan structures. */ |
| 318 struct agere_ext_scan_info { |
| 319 __le16 reserved0; |
| 320 |
| 321 u8 noise; |
| 322 u8 level; |
| 323 u8 rx_flow; |
| 324 u8 rate; |
| 325 __le16 reserved1[2]; |
| 326 |
| 327 __le16 frame_control; |
| 328 __le16 dur_id; |
| 329 u8 addr1[ETH_ALEN]; |
| 330 u8 addr2[ETH_ALEN]; |
| 331 u8 bssid[ETH_ALEN]; |
| 332 __le16 sequence; |
| 333 u8 addr4[ETH_ALEN]; |
| 334 |
| 335 __le16 data_length; |
| 336 |
| 337 /* Next 3 fields do not get filled in. */ |
| 338 u8 daddr[ETH_ALEN]; |
| 339 u8 saddr[ETH_ALEN]; |
| 340 __le16 len_type; |
| 341 |
| 342 __le64 timestamp; |
| 343 __le16 beacon_interval; |
| 344 __le16 capabilities; |
| 345 u8 data[0]; |
| 346 } __packed; |
| 347 |
| 348 #define HERMES_LINKSTATUS_NOT_CONNECTED (0x0000) |
| 349 #define HERMES_LINKSTATUS_CONNECTED (0x0001) |
| 350 #define HERMES_LINKSTATUS_DISCONNECTED (0x0002) |
| 351 #define HERMES_LINKSTATUS_AP_CHANGE (0x0003) |
| 352 #define HERMES_LINKSTATUS_AP_OUT_OF_RANGE (0x0004) |
| 353 #define HERMES_LINKSTATUS_AP_IN_RANGE (0x0005) |
| 354 #define HERMES_LINKSTATUS_ASSOC_FAILED (0x0006) |
| 355 |
| 356 struct hermes_linkstatus { |
| 357 __le16 linkstatus; /* Link status */ |
| 358 } __packed; |
| 359 |
| 360 struct hermes_response { |
| 361 u16 status, resp0, resp1, resp2; |
| 362 }; |
| 363 |
| 364 /* "ID" structure - used for ESSID and station nickname */ |
| 365 struct hermes_idstring { |
| 366 __le16 len; |
| 367 __le16 val[16]; |
| 368 } __packed; |
| 369 |
| 370 struct hermes_multicast { |
| 371 u8 addr[HERMES_MAX_MULTICAST][ETH_ALEN]; |
| 372 } __packed; |
| 373 |
| 374 /* Timeouts */ |
| 375 #define HERMES_BAP_BUSY_TIMEOUT (10000) /* In iterations of ~1us */ |
| 376 |
| 377 struct hermes; |
| 378 |
| 379 /* Functions to access hardware */ |
| 380 struct hermes_ops { |
| 381 int (*init)(struct hermes *hw); |
| 382 int (*cmd_wait)(struct hermes *hw, u16 cmd, u16 parm0, |
| 383 struct hermes_response *resp); |
| 384 int (*init_cmd_wait)(struct hermes *hw, u16 cmd, |
| 385 u16 parm0, u16 parm1, u16 parm2, |
| 386 struct hermes_response *resp); |
| 387 int (*allocate)(struct hermes *hw, u16 size, u16 *fid); |
| 388 int (*read_ltv)(struct hermes *hw, int bap, u16 rid, unsigned buflen, |
| 389 u16 *length, void *buf); |
| 390 int (*write_ltv)(struct hermes *hw, int bap, u16 rid, |
| 391 u16 length, const void *value); |
| 392 int (*bap_pread)(struct hermes *hw, int bap, void *buf, int len, |
| 393 u16 id, u16 offset); |
| 394 int (*bap_pwrite)(struct hermes *hw, int bap, const void *buf, |
| 395 int len, u16 id, u16 offset); |
| 396 int (*read_pda_h)(struct hermes *hw, __le16 *pda, |
| 397 u32 pda_addr, u16 pda_len); |
| 398 int (*program_init)(struct hermes *hw, u32 entry_point); |
| 399 int (*program_end)(struct hermes *hw); |
| 400 int (*program)(struct hermes *hw, const char *buf, |
| 401 u32 addr, u32 len); |
| 402 void (*lock_irqsave)(spinlock_t *lock, unsigned long *flags); |
| 403 void (*unlock_irqrestore)(spinlock_t *lock, unsigned long *flags); |
| 404 void (*lock_irq)(spinlock_t *lock); |
| 405 void (*unlock_irq)(spinlock_t *lock); |
| 406 }; |
| 407 |
| 408 /* Basic control structure */ |
| 409 typedef struct hermes { |
| 410 void __iomem *iobase; |
| 411 int reg_spacing; |
| 412 #define HERMES_16BIT_REGSPACING 0 |
| 413 #define HERMES_32BIT_REGSPACING 1 |
| 414 u16 inten; /* Which interrupts should be enabled? */ |
| 415 bool eeprom_pda; |
| 416 const struct hermes_ops *ops; |
| 417 void *priv; |
| 418 } hermes_t; |
| 419 |
| 420 /* Register access convenience macros */ |
| 421 #define hermes_read_reg(hw, off) \ |
| 422 (ioread16((hw)->iobase + ((off) << (hw)->reg_spacing))) |
| 423 #define hermes_write_reg(hw, off, val) \ |
| 424 (iowrite16((val), (hw)->iobase + ((off) << (hw)->reg_spacing))) |
| 425 #define hermes_read_regn(hw, name) hermes_read_reg((hw), HERMES_##name) |
| 426 #define hermes_write_regn(hw, name, val) \ |
| 427 hermes_write_reg((hw), HERMES_##name, (val)) |
| 428 |
| 429 /* Function prototypes */ |
| 430 void hermes_struct_init(hermes_t *hw, void __iomem *address, int reg_spacing); |
| 431 |
| 432 /* Inline functions */ |
| 433 |
| 434 static inline int hermes_present(hermes_t *hw) |
| 435 { |
| 436 return hermes_read_regn(hw, SWSUPPORT0) == HERMES_MAGIC; |
| 437 } |
| 438 |
| 439 static inline void hermes_set_irqmask(hermes_t *hw, u16 events) |
| 440 { |
| 441 hw->inten = events; |
| 442 hermes_write_regn(hw, INTEN, events); |
| 443 } |
| 444 |
| 445 static inline int hermes_enable_port(hermes_t *hw, int port) |
| 446 { |
| 447 return hw->ops->cmd_wait(hw, HERMES_CMD_ENABLE | (port << 8), |
| 448 0, NULL); |
| 449 } |
| 450 |
| 451 static inline int hermes_disable_port(hermes_t *hw, int port) |
| 452 { |
| 453 return hw->ops->cmd_wait(hw, HERMES_CMD_DISABLE | (port << 8), |
| 454 0, NULL); |
| 455 } |
| 456 |
| 457 /* Initiate an INQUIRE command (tallies or scan). The result will come as an |
| 458 * information frame in __orinoco_ev_info() */ |
| 459 static inline int hermes_inquire(hermes_t *hw, u16 rid) |
| 460 { |
| 461 return hw->ops->cmd_wait(hw, HERMES_CMD_INQUIRE, rid, NULL); |
| 462 } |
| 463 |
| 464 #define HERMES_BYTES_TO_RECLEN(n) ((((n)+1)/2) + 1) |
| 465 #define HERMES_RECLEN_TO_BYTES(n) (((n)-1) * 2) |
| 466 |
| 467 /* Note that for the next two, the count is in 16-bit words, not bytes */ |
| 468 static inline void hermes_read_words(struct hermes *hw, int off, |
| 469 void *buf, unsigned count) |
| 470 { |
| 471 off = off << hw->reg_spacing; |
| 472 ioread16_rep(hw->iobase + off, buf, count); |
| 473 } |
| 474 |
| 475 static inline void hermes_write_bytes(struct hermes *hw, int off, |
| 476 const char *buf, unsigned count) |
| 477 { |
| 478 off = off << hw->reg_spacing; |
| 479 iowrite16_rep(hw->iobase + off, buf, count >> 1); |
| 480 if (unlikely(count & 1)) |
| 481 iowrite8(buf[count - 1], hw->iobase + off); |
| 482 } |
| 483 |
| 484 static inline void hermes_clear_words(struct hermes *hw, int off, |
| 485 unsigned count) |
| 486 { |
| 487 unsigned i; |
| 488 |
| 489 off = off << hw->reg_spacing; |
| 490 |
| 491 for (i = 0; i < count; i++) |
| 492 iowrite16(0, hw->iobase + off); |
| 493 } |
| 494 |
| 495 #define HERMES_READ_RECORD(hw, bap, rid, buf) \ |
| 496 (hw->ops->read_ltv((hw), (bap), (rid), sizeof(*buf), NULL, (buf))) |
| 497 #define HERMES_WRITE_RECORD(hw, bap, rid, buf) \ |
| 498 (hw->ops->write_ltv((hw), (bap), (rid), \ |
| 499 HERMES_BYTES_TO_RECLEN(sizeof(*buf)), (buf))) |
| 500 |
| 501 static inline int hermes_read_wordrec(hermes_t *hw, int bap, u16 rid, u16 *word) |
| 502 { |
| 503 __le16 rec; |
| 504 int err; |
| 505 |
| 506 err = HERMES_READ_RECORD(hw, bap, rid, &rec); |
| 507 *word = le16_to_cpu(rec); |
| 508 return err; |
| 509 } |
| 510 |
| 511 static inline int hermes_write_wordrec(hermes_t *hw, int bap, u16 rid, u16 word) |
| 512 { |
| 513 __le16 rec = cpu_to_le16(word); |
| 514 return HERMES_WRITE_RECORD(hw, bap, rid, &rec); |
| 515 } |
| 516 |
| 517 #endif /* _HERMES_H */ |
OLD | NEW |