Adding ath6kl driver support to compat-wireless

chromeos/compat-wireless/drivers/staging/ath6kl/os/linux/include/wlan_config.h

Index: chromeos/compat-wireless/drivers/staging/ath6kl/os/linux/include/wlan_config.h
diff --git a/chromeos/compat-wireless/drivers/staging/ath6kl/os/linux/include/wlan_config.h b/chromeos/compat-wireless/drivers/staging/ath6kl/os/linux/include/wlan_config.h
new file mode 100644
index 0000000000000000000000000000000000000000..f7d048722226927b40aab690481bbd0ee6667979
--- /dev/null
+++ b/chromeos/compat-wireless/drivers/staging/ath6kl/os/linux/include/wlan_config.h
@@ -0,0 +1,111 @@
+//------------------------------------------------------------------------------
+// Copyright (c) 2004-2010 Atheros Corporation.  All rights reserved.
+// 
+//
+// Permission to use, copy, modify, and/or distribute this software for any
+// purpose with or without fee is hereby granted, provided that the above
+// copyright notice and this permission notice appear in all copies.
+//
+// THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+// WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+// MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+// ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+// WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+// ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+// OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+//
+//
+//------------------------------------------------------------------------------
+//==============================================================================
+// This file contains the tunable configuration items for the WLAN module
+//
+// Author(s): ="Atheros"
+//==============================================================================
+#ifndef _HOST_WLAN_CONFIG_H_
+#define _HOST_WLAN_CONFIG_H_
+
+/* Include definitions here that can be used to tune the WLAN module behavior.
+ * Different customers can tune the behavior as per their needs, here. 
+ */
+
+/* This configuration item when defined will consider the barker preamble 
+ * mentioned in the ERP IE of the beacons from the AP to determine the short 
+ * preamble support sent in the (Re)Assoc request frames.
+ */
+#define WLAN_CONFIG_DONOT_IGNORE_BARKER_IN_ERP 0
+
+/* This config item when defined will not send the power module state transition
+ * failure events that happen during scan, to the host. 
+ */
+#define WLAN_CONFIG_IGNORE_POWER_SAVE_FAIL_EVENT_DURING_SCAN 0
+
+/*
+ * This configuration item enable/disable keepalive support.
+ * Keepalive support: In the absence of any data traffic to AP, null 
+ * frames will be sent to the AP at periodic interval, to keep the association
+ * active. This configuration item defines the periodic interval.
+ * Use value of zero to disable keepalive support
+ * Default: 60 seconds
+ */
+#define WLAN_CONFIG_KEEP_ALIVE_INTERVAL 60 
+
+/*
+ * This configuration item sets the value of disconnect timeout
+ * Firmware delays sending the disconnec event to the host for this
+ * timeout after is gets disconnected from the current AP.
+ * If the firmware successly roams within the disconnect timeout
+ * it sends a new connect event
+ */
+#ifdef ANDROID_ENV
+#define WLAN_CONFIG_DISCONNECT_TIMEOUT 3
+#else
+#define WLAN_CONFIG_DISCONNECT_TIMEOUT 10
+#endif /* ANDROID_ENV */ 
+
+/*
+ * This configuration item disables 11n support. 
+ * 0 - Enable
+ * 1 - Disable
+ */
+#define WLAN_CONFIG_DISABLE_11N         0
+
+/*
+ * This configuration item enable BT clock sharing support
+ * 1 - Enable
+ * 0 - Disable (Default)
+ */
+#define WLAN_CONFIG_BT_SHARING          0
+
+/*
+ * This configuration item sets WIFI OFF policy
+ * 0 - CUT_POWER
+ * 1 - DEEP_SLEEP (Default)
+ */
+#define WLAN_CONFIG_WLAN_OFF                1
+
+/*
+ * This configuration item sets suspend policy
+ * 0 - CUT_POWER (Default)
+ * 1 - DEEP_SLEEP
+ * 2 - WoW
+ * 3 - CUT_POWER if BT OFF (clock sharing designs only)
+ */
+#define WLAN_CONFIG_PM_SUSPEND              0
+
+/*
+ * This configuration item sets suspend policy to use if PM_SUSPEND is
+ * set to WoW and device is not connected at the time of suspend
+ * 0 - CUT_POWER (Default)
+ * 1 - DEEP_SLEEP
+ * 2 - WoW
+ * 3 - CUT_POWER if BT OFF (clock sharing designs only)
+ */
+#define WLAN_CONFIG_PM_WOW2                 0
+
+/*
+ * Platform specific function to power ON/OFF AR6000 
+ * and enable/disable SDIO card detection
+ */
+#define plat_setup_power(on, detect)
+
+#endif /* _HOST_WLAN_CONFIG_H_ */