| Index: chromeos/compat-wireless/drivers/net/wireless/orinoco/hermes.h
|
| diff --git a/chromeos/compat-wireless/drivers/net/wireless/orinoco/hermes.h b/chromeos/compat-wireless/drivers/net/wireless/orinoco/hermes.h
|
| new file mode 100644
|
| index 0000000000000000000000000000000000000000..b3649dd547e3d77d9c3a7ed97f1e6b3449d3a0a6
|
| --- /dev/null
|
| +++ b/chromeos/compat-wireless/drivers/net/wireless/orinoco/hermes.h
|
| @@ -0,0 +1,517 @@
|
| +/* hermes.h
|
| + *
|
| + * Driver core for the "Hermes" wireless MAC controller, as used in
|
| + * the Lucent Orinoco and Cabletron RoamAbout cards. It should also
|
| + * work on the hfa3841 and hfa3842 MAC controller chips used in the
|
| + * Prism I & II chipsets.
|
| + *
|
| + * This is not a complete driver, just low-level access routines for
|
| + * the MAC controller itself.
|
| + *
|
| + * Based on the prism2 driver from Absolute Value Systems' linux-wlan
|
| + * project, the Linux wvlan_cs driver, Lucent's HCF-Light
|
| + * (wvlan_hcf.c) library, and the NetBSD wireless driver.
|
| + *
|
| + * Copyright (C) 2000, David Gibson, Linuxcare Australia.
|
| + * (C) Copyright David Gibson, IBM Corp. 2001-2003.
|
| + *
|
| + * Portions taken from hfa384x.h.
|
| + * Copyright (C) 1999 AbsoluteValue Systems, Inc. All Rights Reserved.
|
| + *
|
| + * This file distributed under the GPL, version 2.
|
| + */
|
| +
|
| +#ifndef _HERMES_H
|
| +#define _HERMES_H
|
| +
|
| +/* Notes on locking:
|
| + *
|
| + * As a module of low level hardware access routines, there is no
|
| + * locking. Users of this module should ensure that they serialize
|
| + * access to the hermes_t structure, and to the hardware
|
| +*/
|
| +
|
| +#include <linux/if_ether.h>
|
| +#include <linux/io.h>
|
| +
|
| +/*
|
| + * Limits and constants
|
| + */
|
| +#define HERMES_ALLOC_LEN_MIN (4)
|
| +#define HERMES_ALLOC_LEN_MAX (2400)
|
| +#define HERMES_LTV_LEN_MAX (34)
|
| +#define HERMES_BAP_DATALEN_MAX (4096)
|
| +#define HERMES_BAP_OFFSET_MAX (4096)
|
| +#define HERMES_PORTID_MAX (7)
|
| +#define HERMES_NUMPORTS_MAX (HERMES_PORTID_MAX+1)
|
| +#define HERMES_PDR_LEN_MAX (260) /* in bytes, from EK */
|
| +#define HERMES_PDA_RECS_MAX (200) /* a guess */
|
| +#define HERMES_PDA_LEN_MAX (1024) /* in bytes, from EK */
|
| +#define HERMES_SCANRESULT_MAX (35)
|
| +#define HERMES_CHINFORESULT_MAX (8)
|
| +#define HERMES_MAX_MULTICAST (16)
|
| +#define HERMES_MAGIC (0x7d1f)
|
| +
|
| +/*
|
| + * Hermes register offsets
|
| + */
|
| +#define HERMES_CMD (0x00)
|
| +#define HERMES_PARAM0 (0x02)
|
| +#define HERMES_PARAM1 (0x04)
|
| +#define HERMES_PARAM2 (0x06)
|
| +#define HERMES_STATUS (0x08)
|
| +#define HERMES_RESP0 (0x0A)
|
| +#define HERMES_RESP1 (0x0C)
|
| +#define HERMES_RESP2 (0x0E)
|
| +#define HERMES_INFOFID (0x10)
|
| +#define HERMES_RXFID (0x20)
|
| +#define HERMES_ALLOCFID (0x22)
|
| +#define HERMES_TXCOMPLFID (0x24)
|
| +#define HERMES_SELECT0 (0x18)
|
| +#define HERMES_OFFSET0 (0x1C)
|
| +#define HERMES_DATA0 (0x36)
|
| +#define HERMES_SELECT1 (0x1A)
|
| +#define HERMES_OFFSET1 (0x1E)
|
| +#define HERMES_DATA1 (0x38)
|
| +#define HERMES_EVSTAT (0x30)
|
| +#define HERMES_INTEN (0x32)
|
| +#define HERMES_EVACK (0x34)
|
| +#define HERMES_CONTROL (0x14)
|
| +#define HERMES_SWSUPPORT0 (0x28)
|
| +#define HERMES_SWSUPPORT1 (0x2A)
|
| +#define HERMES_SWSUPPORT2 (0x2C)
|
| +#define HERMES_AUXPAGE (0x3A)
|
| +#define HERMES_AUXOFFSET (0x3C)
|
| +#define HERMES_AUXDATA (0x3E)
|
| +
|
| +/*
|
| + * CMD register bitmasks
|
| + */
|
| +#define HERMES_CMD_BUSY (0x8000)
|
| +#define HERMES_CMD_AINFO (0x7f00)
|
| +#define HERMES_CMD_MACPORT (0x0700)
|
| +#define HERMES_CMD_RECL (0x0100)
|
| +#define HERMES_CMD_WRITE (0x0100)
|
| +#define HERMES_CMD_PROGMODE (0x0300)
|
| +#define HERMES_CMD_CMDCODE (0x003f)
|
| +
|
| +/*
|
| + * STATUS register bitmasks
|
| + */
|
| +#define HERMES_STATUS_RESULT (0x7f00)
|
| +#define HERMES_STATUS_CMDCODE (0x003f)
|
| +
|
| +/*
|
| + * OFFSET register bitmasks
|
| + */
|
| +#define HERMES_OFFSET_BUSY (0x8000)
|
| +#define HERMES_OFFSET_ERR (0x4000)
|
| +#define HERMES_OFFSET_DATAOFF (0x0ffe)
|
| +
|
| +/*
|
| + * Event register bitmasks (INTEN, EVSTAT, EVACK)
|
| + */
|
| +#define HERMES_EV_TICK (0x8000)
|
| +#define HERMES_EV_WTERR (0x4000)
|
| +#define HERMES_EV_INFDROP (0x2000)
|
| +#define HERMES_EV_INFO (0x0080)
|
| +#define HERMES_EV_DTIM (0x0020)
|
| +#define HERMES_EV_CMD (0x0010)
|
| +#define HERMES_EV_ALLOC (0x0008)
|
| +#define HERMES_EV_TXEXC (0x0004)
|
| +#define HERMES_EV_TX (0x0002)
|
| +#define HERMES_EV_RX (0x0001)
|
| +
|
| +/*
|
| + * Command codes
|
| + */
|
| +/*--- Controller Commands ----------------------------*/
|
| +#define HERMES_CMD_INIT (0x0000)
|
| +#define HERMES_CMD_ENABLE (0x0001)
|
| +#define HERMES_CMD_DISABLE (0x0002)
|
| +#define HERMES_CMD_DIAG (0x0003)
|
| +
|
| +/*--- Buffer Mgmt Commands ---------------------------*/
|
| +#define HERMES_CMD_ALLOC (0x000A)
|
| +#define HERMES_CMD_TX (0x000B)
|
| +
|
| +/*--- Regulate Commands ------------------------------*/
|
| +#define HERMES_CMD_NOTIFY (0x0010)
|
| +#define HERMES_CMD_INQUIRE (0x0011)
|
| +
|
| +/*--- Configure Commands -----------------------------*/
|
| +#define HERMES_CMD_ACCESS (0x0021)
|
| +#define HERMES_CMD_DOWNLD (0x0022)
|
| +
|
| +/*--- Serial I/O Commands ----------------------------*/
|
| +#define HERMES_CMD_READMIF (0x0030)
|
| +#define HERMES_CMD_WRITEMIF (0x0031)
|
| +
|
| +/*--- Debugging Commands -----------------------------*/
|
| +#define HERMES_CMD_TEST (0x0038)
|
| +
|
| +
|
| +/* Test command arguments */
|
| +#define HERMES_TEST_SET_CHANNEL 0x0800
|
| +#define HERMES_TEST_MONITOR 0x0b00
|
| +#define HERMES_TEST_STOP 0x0f00
|
| +
|
| +/* Authentication algorithms */
|
| +#define HERMES_AUTH_OPEN 1
|
| +#define HERMES_AUTH_SHARED_KEY 2
|
| +
|
| +/* WEP settings */
|
| +#define HERMES_WEP_PRIVACY_INVOKED 0x0001
|
| +#define HERMES_WEP_EXCL_UNENCRYPTED 0x0002
|
| +#define HERMES_WEP_HOST_ENCRYPT 0x0010
|
| +#define HERMES_WEP_HOST_DECRYPT 0x0080
|
| +
|
| +/* Symbol hostscan options */
|
| +#define HERMES_HOSTSCAN_SYMBOL_5SEC 0x0001
|
| +#define HERMES_HOSTSCAN_SYMBOL_ONCE 0x0002
|
| +#define HERMES_HOSTSCAN_SYMBOL_PASSIVE 0x0040
|
| +#define HERMES_HOSTSCAN_SYMBOL_BCAST 0x0080
|
| +
|
| +/*
|
| + * Frame structures and constants
|
| + */
|
| +
|
| +#define HERMES_DESCRIPTOR_OFFSET 0
|
| +#define HERMES_802_11_OFFSET (14)
|
| +#define HERMES_802_3_OFFSET (14+32)
|
| +#define HERMES_802_2_OFFSET (14+32+14)
|
| +#define HERMES_TXCNTL2_OFFSET (HERMES_802_3_OFFSET - 2)
|
| +
|
| +#define HERMES_RXSTAT_ERR (0x0003)
|
| +#define HERMES_RXSTAT_BADCRC (0x0001)
|
| +#define HERMES_RXSTAT_UNDECRYPTABLE (0x0002)
|
| +#define HERMES_RXSTAT_MIC (0x0010) /* Frame contains MIC */
|
| +#define HERMES_RXSTAT_MACPORT (0x0700)
|
| +#define HERMES_RXSTAT_PCF (0x1000) /* Frame was received in CF period */
|
| +#define HERMES_RXSTAT_MIC_KEY_ID (0x1800) /* MIC key used */
|
| +#define HERMES_RXSTAT_MSGTYPE (0xE000)
|
| +#define HERMES_RXSTAT_1042 (0x2000) /* RFC-1042 frame */
|
| +#define HERMES_RXSTAT_TUNNEL (0x4000) /* bridge-tunnel encoded frame */
|
| +#define HERMES_RXSTAT_WMP (0x6000) /* Wavelan-II Management Protocol frame */
|
| +
|
| +/* Shift amount for key ID in RXSTAT and TXCTRL */
|
| +#define HERMES_MIC_KEY_ID_SHIFT 11
|
| +
|
| +struct hermes_tx_descriptor {
|
| + __le16 status;
|
| + __le16 reserved1;
|
| + __le16 reserved2;
|
| + __le32 sw_support;
|
| + u8 retry_count;
|
| + u8 tx_rate;
|
| + __le16 tx_control;
|
| +} __packed;
|
| +
|
| +#define HERMES_TXSTAT_RETRYERR (0x0001)
|
| +#define HERMES_TXSTAT_AGEDERR (0x0002)
|
| +#define HERMES_TXSTAT_DISCON (0x0004)
|
| +#define HERMES_TXSTAT_FORMERR (0x0008)
|
| +
|
| +#define HERMES_TXCTRL_TX_OK (0x0002) /* ?? interrupt on Tx complete */
|
| +#define HERMES_TXCTRL_TX_EX (0x0004) /* ?? interrupt on Tx exception */
|
| +#define HERMES_TXCTRL_802_11 (0x0008) /* We supply 802.11 header */
|
| +#define HERMES_TXCTRL_MIC (0x0010) /* 802.3 + TKIP */
|
| +#define HERMES_TXCTRL_MIC_KEY_ID (0x1800) /* MIC Key ID mask */
|
| +#define HERMES_TXCTRL_ALT_RTRY (0x0020)
|
| +
|
| +/* Inquiry constants and data types */
|
| +
|
| +#define HERMES_INQ_TALLIES (0xF100)
|
| +#define HERMES_INQ_SCAN (0xF101)
|
| +#define HERMES_INQ_CHANNELINFO (0xF102)
|
| +#define HERMES_INQ_HOSTSCAN (0xF103)
|
| +#define HERMES_INQ_HOSTSCAN_SYMBOL (0xF104)
|
| +#define HERMES_INQ_LINKSTATUS (0xF200)
|
| +#define HERMES_INQ_SEC_STAT_AGERE (0xF202)
|
| +
|
| +struct hermes_tallies_frame {
|
| + __le16 TxUnicastFrames;
|
| + __le16 TxMulticastFrames;
|
| + __le16 TxFragments;
|
| + __le16 TxUnicastOctets;
|
| + __le16 TxMulticastOctets;
|
| + __le16 TxDeferredTransmissions;
|
| + __le16 TxSingleRetryFrames;
|
| + __le16 TxMultipleRetryFrames;
|
| + __le16 TxRetryLimitExceeded;
|
| + __le16 TxDiscards;
|
| + __le16 RxUnicastFrames;
|
| + __le16 RxMulticastFrames;
|
| + __le16 RxFragments;
|
| + __le16 RxUnicastOctets;
|
| + __le16 RxMulticastOctets;
|
| + __le16 RxFCSErrors;
|
| + __le16 RxDiscards_NoBuffer;
|
| + __le16 TxDiscardsWrongSA;
|
| + __le16 RxWEPUndecryptable;
|
| + __le16 RxMsgInMsgFragments;
|
| + __le16 RxMsgInBadMsgFragments;
|
| + /* Those last are probably not available in very old firmwares */
|
| + __le16 RxDiscards_WEPICVError;
|
| + __le16 RxDiscards_WEPExcluded;
|
| +} __packed;
|
| +
|
| +/* Grabbed from wlan-ng - Thanks Mark... - Jean II
|
| + * This is the result of a scan inquiry command */
|
| +/* Structure describing info about an Access Point */
|
| +struct prism2_scan_apinfo {
|
| + __le16 channel; /* Channel where the AP sits */
|
| + __le16 noise; /* Noise level */
|
| + __le16 level; /* Signal level */
|
| + u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */
|
| + __le16 beacon_interv; /* Beacon interval */
|
| + __le16 capabilities; /* Capabilities */
|
| + __le16 essid_len; /* ESSID length */
|
| + u8 essid[32]; /* ESSID of the network */
|
| + u8 rates[10]; /* Bit rate supported */
|
| + __le16 proberesp_rate; /* Data rate of the response frame */
|
| + __le16 atim; /* ATIM window time, Kus (hostscan only) */
|
| +} __packed;
|
| +
|
| +/* Same stuff for the Lucent/Agere card.
|
| + * Thanks to h1kari <h1kari AT dachb0den.com> - Jean II */
|
| +struct agere_scan_apinfo {
|
| + __le16 channel; /* Channel where the AP sits */
|
| + __le16 noise; /* Noise level */
|
| + __le16 level; /* Signal level */
|
| + u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */
|
| + __le16 beacon_interv; /* Beacon interval */
|
| + __le16 capabilities; /* Capabilities */
|
| + /* bits: 0-ess, 1-ibss, 4-privacy [wep] */
|
| + __le16 essid_len; /* ESSID length */
|
| + u8 essid[32]; /* ESSID of the network */
|
| +} __packed;
|
| +
|
| +/* Moustafa: Scan structure for Symbol cards */
|
| +struct symbol_scan_apinfo {
|
| + u8 channel; /* Channel where the AP sits */
|
| + u8 unknown1; /* 8 in 2.9x and 3.9x f/w, 0 otherwise */
|
| + __le16 noise; /* Noise level */
|
| + __le16 level; /* Signal level */
|
| + u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */
|
| + __le16 beacon_interv; /* Beacon interval */
|
| + __le16 capabilities; /* Capabilities */
|
| + /* bits: 0-ess, 1-ibss, 4-privacy [wep] */
|
| + __le16 essid_len; /* ESSID length */
|
| + u8 essid[32]; /* ESSID of the network */
|
| + __le16 rates[5]; /* Bit rate supported */
|
| + __le16 basic_rates; /* Basic rates bitmask */
|
| + u8 unknown2[6]; /* Always FF:FF:FF:FF:00:00 */
|
| + u8 unknown3[8]; /* Always 0, appeared in f/w 3.91-68 */
|
| +} __packed;
|
| +
|
| +union hermes_scan_info {
|
| + struct agere_scan_apinfo a;
|
| + struct prism2_scan_apinfo p;
|
| + struct symbol_scan_apinfo s;
|
| +};
|
| +
|
| +/* Extended scan struct for HERMES_INQ_CHANNELINFO.
|
| + * wl_lkm calls this an ACS scan (Automatic Channel Select).
|
| + * Keep out of union hermes_scan_info because it is much bigger than
|
| + * the older scan structures. */
|
| +struct agere_ext_scan_info {
|
| + __le16 reserved0;
|
| +
|
| + u8 noise;
|
| + u8 level;
|
| + u8 rx_flow;
|
| + u8 rate;
|
| + __le16 reserved1[2];
|
| +
|
| + __le16 frame_control;
|
| + __le16 dur_id;
|
| + u8 addr1[ETH_ALEN];
|
| + u8 addr2[ETH_ALEN];
|
| + u8 bssid[ETH_ALEN];
|
| + __le16 sequence;
|
| + u8 addr4[ETH_ALEN];
|
| +
|
| + __le16 data_length;
|
| +
|
| + /* Next 3 fields do not get filled in. */
|
| + u8 daddr[ETH_ALEN];
|
| + u8 saddr[ETH_ALEN];
|
| + __le16 len_type;
|
| +
|
| + __le64 timestamp;
|
| + __le16 beacon_interval;
|
| + __le16 capabilities;
|
| + u8 data[0];
|
| +} __packed;
|
| +
|
| +#define HERMES_LINKSTATUS_NOT_CONNECTED (0x0000)
|
| +#define HERMES_LINKSTATUS_CONNECTED (0x0001)
|
| +#define HERMES_LINKSTATUS_DISCONNECTED (0x0002)
|
| +#define HERMES_LINKSTATUS_AP_CHANGE (0x0003)
|
| +#define HERMES_LINKSTATUS_AP_OUT_OF_RANGE (0x0004)
|
| +#define HERMES_LINKSTATUS_AP_IN_RANGE (0x0005)
|
| +#define HERMES_LINKSTATUS_ASSOC_FAILED (0x0006)
|
| +
|
| +struct hermes_linkstatus {
|
| + __le16 linkstatus; /* Link status */
|
| +} __packed;
|
| +
|
| +struct hermes_response {
|
| + u16 status, resp0, resp1, resp2;
|
| +};
|
| +
|
| +/* "ID" structure - used for ESSID and station nickname */
|
| +struct hermes_idstring {
|
| + __le16 len;
|
| + __le16 val[16];
|
| +} __packed;
|
| +
|
| +struct hermes_multicast {
|
| + u8 addr[HERMES_MAX_MULTICAST][ETH_ALEN];
|
| +} __packed;
|
| +
|
| +/* Timeouts */
|
| +#define HERMES_BAP_BUSY_TIMEOUT (10000) /* In iterations of ~1us */
|
| +
|
| +struct hermes;
|
| +
|
| +/* Functions to access hardware */
|
| +struct hermes_ops {
|
| + int (*init)(struct hermes *hw);
|
| + int (*cmd_wait)(struct hermes *hw, u16 cmd, u16 parm0,
|
| + struct hermes_response *resp);
|
| + int (*init_cmd_wait)(struct hermes *hw, u16 cmd,
|
| + u16 parm0, u16 parm1, u16 parm2,
|
| + struct hermes_response *resp);
|
| + int (*allocate)(struct hermes *hw, u16 size, u16 *fid);
|
| + int (*read_ltv)(struct hermes *hw, int bap, u16 rid, unsigned buflen,
|
| + u16 *length, void *buf);
|
| + int (*write_ltv)(struct hermes *hw, int bap, u16 rid,
|
| + u16 length, const void *value);
|
| + int (*bap_pread)(struct hermes *hw, int bap, void *buf, int len,
|
| + u16 id, u16 offset);
|
| + int (*bap_pwrite)(struct hermes *hw, int bap, const void *buf,
|
| + int len, u16 id, u16 offset);
|
| + int (*read_pda_h)(struct hermes *hw, __le16 *pda,
|
| + u32 pda_addr, u16 pda_len);
|
| + int (*program_init)(struct hermes *hw, u32 entry_point);
|
| + int (*program_end)(struct hermes *hw);
|
| + int (*program)(struct hermes *hw, const char *buf,
|
| + u32 addr, u32 len);
|
| + void (*lock_irqsave)(spinlock_t *lock, unsigned long *flags);
|
| + void (*unlock_irqrestore)(spinlock_t *lock, unsigned long *flags);
|
| + void (*lock_irq)(spinlock_t *lock);
|
| + void (*unlock_irq)(spinlock_t *lock);
|
| +};
|
| +
|
| +/* Basic control structure */
|
| +typedef struct hermes {
|
| + void __iomem *iobase;
|
| + int reg_spacing;
|
| +#define HERMES_16BIT_REGSPACING 0
|
| +#define HERMES_32BIT_REGSPACING 1
|
| + u16 inten; /* Which interrupts should be enabled? */
|
| + bool eeprom_pda;
|
| + const struct hermes_ops *ops;
|
| + void *priv;
|
| +} hermes_t;
|
| +
|
| +/* Register access convenience macros */
|
| +#define hermes_read_reg(hw, off) \
|
| + (ioread16((hw)->iobase + ((off) << (hw)->reg_spacing)))
|
| +#define hermes_write_reg(hw, off, val) \
|
| + (iowrite16((val), (hw)->iobase + ((off) << (hw)->reg_spacing)))
|
| +#define hermes_read_regn(hw, name) hermes_read_reg((hw), HERMES_##name)
|
| +#define hermes_write_regn(hw, name, val) \
|
| + hermes_write_reg((hw), HERMES_##name, (val))
|
| +
|
| +/* Function prototypes */
|
| +void hermes_struct_init(hermes_t *hw, void __iomem *address, int reg_spacing);
|
| +
|
| +/* Inline functions */
|
| +
|
| +static inline int hermes_present(hermes_t *hw)
|
| +{
|
| + return hermes_read_regn(hw, SWSUPPORT0) == HERMES_MAGIC;
|
| +}
|
| +
|
| +static inline void hermes_set_irqmask(hermes_t *hw, u16 events)
|
| +{
|
| + hw->inten = events;
|
| + hermes_write_regn(hw, INTEN, events);
|
| +}
|
| +
|
| +static inline int hermes_enable_port(hermes_t *hw, int port)
|
| +{
|
| + return hw->ops->cmd_wait(hw, HERMES_CMD_ENABLE | (port << 8),
|
| + 0, NULL);
|
| +}
|
| +
|
| +static inline int hermes_disable_port(hermes_t *hw, int port)
|
| +{
|
| + return hw->ops->cmd_wait(hw, HERMES_CMD_DISABLE | (port << 8),
|
| + 0, NULL);
|
| +}
|
| +
|
| +/* Initiate an INQUIRE command (tallies or scan). The result will come as an
|
| + * information frame in __orinoco_ev_info() */
|
| +static inline int hermes_inquire(hermes_t *hw, u16 rid)
|
| +{
|
| + return hw->ops->cmd_wait(hw, HERMES_CMD_INQUIRE, rid, NULL);
|
| +}
|
| +
|
| +#define HERMES_BYTES_TO_RECLEN(n) ((((n)+1)/2) + 1)
|
| +#define HERMES_RECLEN_TO_BYTES(n) (((n)-1) * 2)
|
| +
|
| +/* Note that for the next two, the count is in 16-bit words, not bytes */
|
| +static inline void hermes_read_words(struct hermes *hw, int off,
|
| + void *buf, unsigned count)
|
| +{
|
| + off = off << hw->reg_spacing;
|
| + ioread16_rep(hw->iobase + off, buf, count);
|
| +}
|
| +
|
| +static inline void hermes_write_bytes(struct hermes *hw, int off,
|
| + const char *buf, unsigned count)
|
| +{
|
| + off = off << hw->reg_spacing;
|
| + iowrite16_rep(hw->iobase + off, buf, count >> 1);
|
| + if (unlikely(count & 1))
|
| + iowrite8(buf[count - 1], hw->iobase + off);
|
| +}
|
| +
|
| +static inline void hermes_clear_words(struct hermes *hw, int off,
|
| + unsigned count)
|
| +{
|
| + unsigned i;
|
| +
|
| + off = off << hw->reg_spacing;
|
| +
|
| + for (i = 0; i < count; i++)
|
| + iowrite16(0, hw->iobase + off);
|
| +}
|
| +
|
| +#define HERMES_READ_RECORD(hw, bap, rid, buf) \
|
| + (hw->ops->read_ltv((hw), (bap), (rid), sizeof(*buf), NULL, (buf)))
|
| +#define HERMES_WRITE_RECORD(hw, bap, rid, buf) \
|
| + (hw->ops->write_ltv((hw), (bap), (rid), \
|
| + HERMES_BYTES_TO_RECLEN(sizeof(*buf)), (buf)))
|
| +
|
| +static inline int hermes_read_wordrec(hermes_t *hw, int bap, u16 rid, u16 *word)
|
| +{
|
| + __le16 rec;
|
| + int err;
|
| +
|
| + err = HERMES_READ_RECORD(hw, bap, rid, &rec);
|
| + *word = le16_to_cpu(rec);
|
| + return err;
|
| +}
|
| +
|
| +static inline int hermes_write_wordrec(hermes_t *hw, int bap, u16 rid, u16 word)
|
| +{
|
| + __le16 rec = cpu_to_le16(word);
|
| + return HERMES_WRITE_RECORD(hw, bap, rid, &rec);
|
| +}
|
| +
|
| +#endif /* _HERMES_H */
|
|
|